SBC SBC-381H Installation Guide

WAFER-945GSE 3.5” Motherboard Page iWAFER-945GSE 3.5” Motherboard , WAFER-945GSE3.5" SBC with Intel® Atom™ Processor with support for VGA and L

WAFER-945GSE 3.5” MotherboardPage x 98H5.5.6 LVDS Voltage Selection...

WAFER-945GSE 3.5” MotherboardPage 80 NOTE: The SATA power cable described below is an optional item and must be pre-ordered. The SATA power cable i

WAFER-945GSE 3.5” Motherboard Page 81the WAFER-945GSE 40-pin serial port connector. See 810HFigure 5-16. Step 3: Insert the cable connectors. Once

WAFER-945GSE 3.5” MotherboardPage 82 Chapter 3. Step 2: Insert the cable connectors. Insert one connector into each serial port box headers. See Fi

WAFER-945GSE 3.5” Motherboard Page 83Step 2: Insert the cable connector. Align the cable connector with the onboard connector. Make sure the pin 1o

WAFER-945GSE 3.5” MotherboardPage 84 Step 0: Figure 5-15: Serial Device Connector 5.7.6 Keyboard/Mouse Y-cable Connector The WAFER-945GSE is shippe

WAFER-945GSE 3.5” Motherboard Page 85connector to the on-board connectors. See 816HFigure 5-16. Figure 5-16: Keyboard/mouse Y-cable Connection Step

WAFER-945GSE 3.5” MotherboardPage 86 In, connects to a microphone. The remaining two audio jacks, Line-In and Line-Out, connect to two speakers. To

WAFER-945GSE 3.5” Motherboard Page 87Chapter 3. WARNING: If the USB pins are not properly aligned, the USB device can burn out. Step 2: Align the

WAFER-945GSE 3.5” MotherboardPage 88  RJ-45 Ethernet cable connectors  Serial port devices  USB devices  VGA monitors To install these devic

WAFER-945GSE 3.5” Motherboard Page 89Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into t

WAFER-945GSE 3.5” Motherboard Page xi132H6.3.5.1 ACPI configuration ...

WAFER-945GSE 3.5” MotherboardPage 90 5.8.3 USB Connection (Dual Connector) The external USB Series "A" receptacle connectors provide eas

WAFER-945GSE 3.5” Motherboard Page 915.8.4 VGA Monitor Connection The WAFER-945GSE has a single female DB-15 connector on the external peripheral in

WAFER-945GSE 3.5” MotherboardPage 92 5.9 Heat Sink Enclosure WARNING: Never run the WAFER-945GSE without the heat sink secured to the board. The he

WAFER-945GSE 3.5” Motherboard Page 93 Figure 5-23: Heat Sink Retention Screws

WAFER-945GSE 3.5” MotherboardPage 94 6 BIOS Screens Chapter 6

WAFER-945GSE 3.5” Motherboard Page 956.1 Introduction A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows

WAFER-945GSE 3.5” MotherboardPage 96 F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 /F3 key Change color from

WAFER-945GSE 3.5” Motherboard Page 976.2 Main The Main BIOS menu (864H823HBIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu

WAFER-945GSE 3.5” MotherboardPage 98 o Count: The number of CPUs on the motherboard  System Memory: Displays the auto-detected system memory. o

WAFER-945GSE 3.5” Motherboard Page 99BIOS Menu 2: Advanced 6.3.1 CPU Configuration Use the CPU Configuration menu (873H832HBIOS Menu 3) to view deta

WAFER-945GSE 3.5” MotherboardPage xii 164HE.3 MEMORY ADDRESS MAP...

WAFER-945GSE 3.5” MotherboardPage 100 BIOS Menu 3: CPU Configuration The CPU Configuration menu (874H833HBIOS Menu 3) lists the following CPU detail

WAFER-945GSE 3.5” Motherboard Page 101BIOS Menu 4: IDE Configuration  ATA/IDE Configurations [Compatible] Use the ATA/IDE Configurations option to

WAFER-945GSE 3.5” MotherboardPage 102  Legacy IDE Channels [PATA Pri, SATA Sec]  SATA Only Only the SATA drives are enabled.  SATA Pri, PATA S

WAFER-945GSE 3.5” Motherboard Page 103BIOS Menu 5: IDE Master and IDE Slave Configuration  Auto-Detected Drive Parameters The “grayed-out” items i

WAFER-945GSE 3.5” MotherboardPage 104 interrupt if block mode is not used. Block mode allows transfers of up to 64 KB per interrupt.  PIO Mode: In

WAFER-945GSE 3.5” Motherboard Page 105 LBA/Large Mode [Auto] Use the LBA/Large Mode option to disable or enable BIOS to auto detects LBA (Logical

WAFER-945GSE 3.5” MotherboardPage 106  0 PIO mode 0 selected with a maximum transfer rate of 3.3MBps  1 PIO mode 1 selected with a maximum tra

WAFER-945GSE 3.5” Motherboard Page 107 UDMA1 Ultra DMA mode 0 selected with a maximum data transfer rate of 16.6MBps  UDMA1 Ultra DMA mode 1

WAFER-945GSE 3.5” MotherboardPage 108  Disabled Prevents the BIOS from using 32-bit data transfers.  Enabled DEFAULT Allows BIOS to use 32-bit

WAFER-945GSE 3.5” Motherboard Page 109address is IRQ4  3E8/IRQ4 Serial Port 1 I/O port address is 3E8 and the interrupt address is IRQ4  2E8/IRQ

WAFER-945GSE 3.5” Motherboard Page xiiiList of Figures 167HFigure 1-1: WAFER-945GSE...

WAFER-945GSE 3.5” MotherboardPage 110 Use the Serial Port3 IRQ option to select the interrupt address for serial port 3.  10 Serial port 3 IRQ ad

WAFER-945GSE 3.5” Motherboard Page 111 2F0 DEFAULT Serial port 5 I/O port address is 2F0  2E0 Serial port 5 I/O port address is 2E0  Serial Po

WAFER-945GSE 3.5” MotherboardPage 112 BIOS Menu 7: Hardware Health Configuration  CPU FAN Mode Setting [Full On Mode] Use the CPU FAN Mode Setting

WAFER-945GSE 3.5” Motherboard Page 113 CPU Fan Start PWM  Slope PWM 1 When the CPU FAN Mode Setting option is in the PWM Manual Mode, the follow

WAFER-945GSE 3.5” MotherboardPage 114 The CPU Temp. Limit of Start option can only be set if the CPU FAN Mode Setting option is set to Automatic Mod

WAFER-945GSE 3.5” Motherboard Page 115 16 PWM  32 PWM  64 PWM The following system parameters and values are shown. The system parameters that

WAFER-945GSE 3.5” MotherboardPage 116 BIOS Menu 8: Power Configuration 6.3.5.1 ACPI configuration The ACPI Configuration menu (880H840HBIOS Menu 9)

WAFER-945GSE 3.5” Motherboard Page 117BIOS Menu 9: ACPI Configuration  Suspend Mode [S1(POS)] Use the Suspend Mode BIOS option to specify the slee

WAFER-945GSE 3.5” MotherboardPage 118 BIOS Menu 10:Advanced Power Management Configuration  Restore on AC Power Loss [Last State] Use the Restore

WAFER-945GSE 3.5” Motherboard Page 119turned on or off  Suspend When the power button is pressed the system goes into suspend mode  Resume on K

WAFER-945GSE 3.5” MotherboardPage xiv 195HFigure 4-12: PCIe Mini Card Slot Location ...5

WAFER-945GSE 3.5” MotherboardPage 120 activity  Resume On RTC Alarm [Disabled] Use the Resume On RTC Alarm option to specify the time the system s

WAFER-945GSE 3.5” Motherboard Page 121BIOS Menu 11: Remote Access Configuration [Advanced]  Remote Access [Disabled] Use the Remote Access option

WAFER-945GSE 3.5” MotherboardPage 122  Terminal Type  VT-UTF8 Combo Key Support These configuration options are discussed below.  Serial Port

WAFER-945GSE 3.5” Motherboard Page 123 Flow Control [None] Use the Flow Control option to report the flow control method for the console redirecti

WAFER-945GSE 3.5” MotherboardPage 124 The VT100 Terminal Definition is the standard convention used to configure and conduct emergency management ta

WAFER-945GSE 3.5” Motherboard Page 125BIOS Menu 12: USB Configuration  USB Functions [Enabled] Use the USB Function option to enable or disable th

WAFER-945GSE 3.5” MotherboardPage 126 The USB2.0 Controller Mode BIOS option sets the speed of the USB2.0 controller.  FullSpeed The controller

WAFER-945GSE 3.5” Motherboard Page 127 BIOS Menu 13: PCI/PnP Configuration  IRQ# [Available] Use the IRQ# address to specify what IRQs can be as

WAFER-945GSE 3.5” MotherboardPage 128  IRQ9  IRQ10  IRQ 11  IRQ 14  IRQ 15  DMA Channel# [Available] Use the DMA Channel# option to assi

WAFER-945GSE 3.5” Motherboard Page 129 64K 54KB reserved for legacy ISA devices 6.5 Boot Use the Boot menu (885H845HBIOS Menu 14) to configure sy

WAFER-945GSE 3.5” Motherboard Page xv227HFigure 5-22: VGA Connector...

WAFER-945GSE 3.5” MotherboardPage 130 BIOS Menu 15: Boot Settings Configuration  Quick Boot [Enabled] Use the Quick Boot BIOS option to make the c

WAFER-945GSE 3.5” Motherboard Page 131The AddOn ROM Display Mode option allows add-on ROM (read-only memory) messages to be displayed.  Force BIOS

WAFER-945GSE 3.5” MotherboardPage 132  Enabled DEFAULT Can be booted from a remote system through the LAN 6.5.2 Boot Device Priority Use the Boot D

WAFER-945GSE 3.5” Motherboard Page 1336.6 Security Use the Security menu (888H848HBIOS Menu 17) to set system and user passwords. BIOS Menu 17: Secu

WAFER-945GSE 3.5” MotherboardPage 134 password. After the password has been added, Install appears next to Change User Password. 6.7 Chipset Use the

WAFER-945GSE 3.5” Motherboard Page 1356.7.1 North Bridge Chipset Configuration Use the North Bridge Chipset Configuration menu (890H850HBIOS Menu 18

WAFER-945GSE 3.5” MotherboardPage 136  Internal Graphics Mode Select [Enable, 8MB] The Internal Graphic Mode Select option determines the amount o

WAFER-945GSE 3.5” Motherboard Page 137 Maximum DVMT  Boot Display Device [Auto] The Boot Display Device BIOS option selects the display device t

WAFER-945GSE 3.5” MotherboardPage 138 BIOS Menu 20:SouthBridge Chipset Configuration  Audio Controller [All Disabled] The Audio Controller option

WAFER-945GSE 3.5” Motherboard Page 139BIOS Menu 21:Exit  Save Changes and Exit Use the Save Changes and Exit option to save the changes made t

WAFER-945GSE 3.5” MotherboardPage xvi List of Tables 255HTable 1-1: Technical Specifications ...

WAFER-945GSE 3.5” MotherboardPage 140  Load Optimal Defaults Use the Load Optimal Defaults option to load the optimal default values for each of t

WAFER-945GSE 3.5” Motherboard Page 141 7 Software Drivers Chapter 7

WAFER-945GSE 3.5” MotherboardPage 142 7.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product

WAFER-945GSE 3.5” Motherboard Page 143 Figure 7-1: Start Up Screen Step 3: Click WAFER-945GSE. Step 4: The screen in appears. Figure 7-2: Select

WAFER-945GSE 3.5” MotherboardPage 144 manual describes the installation for a Windows XP operating system. Step 6: The list of drivers in 854HFigur

WAFER-945GSE 3.5” Motherboard Page 145 Figure 7-4: Chipset Driver Screen Step 4: When the setup files are completely extracted the Welcome Screen i

WAFER-945GSE 3.5” MotherboardPage 146 Step 6: The license agreement in 859HFigure 7-6 appears. Step 7: Read the License Agreement. Step 8: Click

WAFER-945GSE 3.5” Motherboard Page 147 Figure 7-7: Chipset Driver Read Me File Step 11: Setup Operations are performed as shown in 861HFigure 7-8.

WAFER-945GSE 3.5” MotherboardPage 148 Figure 7-8: Chipset Driver Setup Operations Step 12: Once the Setup Operations are complete, click the Next i

WAFER-945GSE 3.5” Motherboard Page 149 Figure 7-9: Chipset Driver Installation Finish Screen 7.4 VGA Driver Installation To install the VGA driver,

WAFER-945GSE 3.5” Motherboard Page xvii283HTable 5-3: CF Card Setup Jumper Settings...680

WAFER-945GSE 3.5” MotherboardPage 150 Figure 7-10: VGA Driver Read Me File Step 5: The installation files are extracted. See 866HFigure 7-11. Fig

WAFER-945GSE 3.5” Motherboard Page 151 Figure 7-12: VGA Driver Welcome Screen Step 7: Click Next to continue. Step 8: The license agreement in 868

WAFER-945GSE 3.5” MotherboardPage 152 Figure 7-13: VGA Driver License Agreement Step 11: The Read Me file in 869HFigure 7-14 appears. Step 12: Clic

WAFER-945GSE 3.5” Motherboard Page 153 Figure 7-15: VGA Driver Setup Operations Step 14: Once the Setup Operations are complete, click the Next icon

WAFER-945GSE 3.5” MotherboardPage 154 7.5 LAN Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver

WAFER-945GSE 3.5” Motherboard Page 155 Figure 7-18: LAN Driver Welcome Screen Step 7: The program begins to install. Step 8: The installation prog

WAFER-945GSE 3.5” MotherboardPage 156 Step 9: When the driver installation is complete, the screen in 877HFigure 7-20 appears.Step 0: Figure 7-20:

WAFER-945GSE 3.5” Motherboard Page 157 Figure 7-21: Audio Driver Options Step 4: Select “2-AC’97” in 881HFigure 7-21 Step 5: The installation file

WAFER-945GSE 3.5” MotherboardPage 158 Step 7: Click Next to continue. Figure 7-23: AC’97 Driver Installation Welcome Screen Step 8: The Verificat

WAFER-945GSE 3.5” Motherboard Page 159Step 10: The driver installation begins. See 885HFigure 7-25. Figure 7-25: AC’97 Driver Installation Step 11:

WAFER-945GSE 3.5” MotherboardPage xviii List of BIOS Menus 290HMenu 1: Main...

WAFER-945GSE 3.5” MotherboardPage 160 A BIOS Menu Options Appendix A

WAFER-945GSE 3.5” Motherboard Page 161 314H System Overview...

WAFER-945GSE 3.5” MotherboardPage 162 345H Suspend Mode [S1(POS)] ...

WAFER-945GSE 3.5” Motherboard Page 163377H Quiet Boot [Disabled]...

WAFER-945GSE 3.5” MotherboardPage 164 B Terminology Appendix B

WAFER-945GSE 3.5” Motherboard Page 165 AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configu

WAFER-945GSE 3.5” MotherboardPage 166 computer is usually a male DE-9 connector. DAC The Digital-to-Analog Converter (DAC) converts digital signals

WAFER-945GSE 3.5” Motherboard Page 167MAC The Media Access Control (MAC) protocol enables several terminals or network nodes to communicate in a LA

WAFER-945GSE 3.5” MotherboardPage 168 asynchronous communications on the system and manages the system’s serial communication (COM) ports. UHCI The

WAFER-945GSE 3.5” Motherboard Page 169 C DIO Interface Appendix C

WAFER-945GSE 3.5” Motherboard Page xixTHIS PAGE IS INTENTIONALLY LEFT BLANK

WAFER-945GSE 3.5” MotherboardPage 170 C.1 DIO Interface Introduction The DIO connector on the WAFER-945GSE is interfaced to GPIO ports on the ITE IT

WAFER-945GSE 3.5” Motherboard Page 171C.3 Assembly Language Samples C.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the

WAFER-945GSE 3.5” MotherboardPage 172 D Watchdog Timer Appendix D

WAFER-945GSE 3.5” Motherboard Page 173 NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website vis

WAFER-945GSE 3.5” MotherboardPage 174 NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. Ex

WAFER-945GSE 3.5” Motherboard Page 175 E Address Mapping Appendix E

WAFER-945GSE 3.5” MotherboardPage 176 E.1 I/O Address Map

WAFER-945GSE 3.5” Motherboard Page 177 Table E-1: IO Address Map

WAFER-945GSE 3.5” MotherboardPage 178 E.2 IRQ Address Map Table E-2: IRQ Address Map

WAFER-945GSE 3.5” Motherboard Page 179E.3 Memory Address Map Table E-3: Memory Address Map

WAFER-945GSE 3.5” MotherboardPage ii Revision Date Version Changes 26 May, 2009 1.03 Modified LVDS connector description in Section 4.3.10 12 March

WAFER-945GSE 3.5” MotherboardPage 180 F Hazardous Materials Disclosure Appendix F

WAFER-945GSE 3.5” Motherboard Page 181F.1 Hazardous Material Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without

WAFER-945GSE 3.5” MotherboardPage 182 Toxic or Hazardous Substances and Elements Part Name Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium

WAFER-945GSE 3.5” Motherboard Page 183此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品

WAFER-945GSE 3.5” Motherboard Page 1 1 Introduction Chapter 1

WAFER-945GSE 3.5” MotherboardPage 2 1.1 Overview Figure 1-1: WAFER-945GSE 1.1.1 WAFER-945GSE Introduction The WAFER-945GSE 3.5” motherboards are em

WAFER-945GSE 3.5” Motherboard Page 3Figure 1-2: WAFER-945GSE Overview [Front View] 1.2.2 WAFER-945GSE Peripheral Connectors and Jumpers The WAFER-94

WAFER-945GSE 3.5” MotherboardPage 4  1 x Power button connector  1 x Reset button connector  1 x 4-port RS-232 serial port connector  1 x RS

WAFER-945GSE 3.5” Motherboard Page 5System Chipset Northbridge: Intel® 945GSE Southbridge: Intel® ICH7-M Memory One 200-pin SO-DIMM socket supports

WAFER-945GSE 3.5” MotherboardPage 6 Power Supply 5.0 V only 12 V for LCD/System Fan AT and ATX support Power Consumption 5V @ 2.94 A (1.6 GHz Intel

WAFER-945GSE 3.5” Motherboard Page 7 2 Detailed Specifications Chapter 2

WAFER-945GSE 3.5” MotherboardPage 8 2.1 Dimensions 2.1.1 Board Dimensions The dimensions of the board are shown below:

WAFER-945GSE 3.5” Motherboard Page 9 Figure 2-1: WAFER-945GSE Dimensions (mm) 2.1.2 External Interface Panel Dimensions External peripheral interfac

WAFER-945GSE 3.5” Motherboard Page iiiCopyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order

WAFER-945GSE 3.5” MotherboardPage 10 Figure 2-3: Data Flow Block Diagram 2.3 Embedded WAFER-945GSE Processor 2.3.1 Overview The WAFER-945GSE comes

WAFER-945GSE 3.5” Motherboard Page 11cache. The low power processor has a maximum power of 2.5 W. The processor is covered with a heat sink and is s

WAFER-945GSE 3.5” MotherboardPage 12  Thermal management support via Intel® Thermal Monitor 1 and Intel Thermal Monitor 2  FSB Lane Reversal for

WAFER-945GSE 3.5” Motherboard Page 132.4 Intel 945GSE Northbridge Chipset 2.4.1 Intel® 945GSE Overview The Intel 945GSE Graphics and Memory Controll

WAFER-945GSE 3.5” MotherboardPage 14 Figure 2-6: DDR2 SO-DIMM Socket 2.4.3 Intel® 945GSE Graphics The Intel® 945GSE supports CRT and LVDS. The inte

WAFER-945GSE 3.5” Motherboard Page 15 4x pixel rate HWMC  Microsoft DirectX* 9.1 operating system  Intermediate Z in Classic Rendering  Inte

WAFER-945GSE 3.5” MotherboardPage 16  Support for CRT Hot Plug 2.4.3.2 LVDS Interface The LVDS interface is connected directly to one of the LVDS

WAFER-945GSE 3.5” Motherboard Page 172.5 Intel® ICH7-M Southbridge Chipset 2.5.1 Intel® ICH7-M Overview The Intel® ICH7-M southbridge chipset is con

WAFER-945GSE 3.5” MotherboardPage 18 o Interrupt controller o Timer functions  Integrated SATA host controller with DMA operations interfaced to

WAFER-945GSE 3.5” Motherboard Page 19 Meets performance requirements for audio on PC99/2001 systems  Meets Microsoft WHQL/WLP 2.0 audio requir

WAFER-945GSE 3.5” MotherboardPage iv Manual Conventions WARNING! Warnings appear where overlooked details may cause damage to the equipment or resu

WAFER-945GSE 3.5” MotherboardPage 20 2.5.3 Intel® ICH7-M Low Pin Count (LPC) Interface The ICH7-M LPC interface complies with the LPC 1.1 specificat

WAFER-945GSE 3.5” Motherboard Page 21 Figure 2-11: Realtek RTL8111C PCIe GbE Controllers The Realtek RTL8111C PCIe GbE controllers combine a triple-

WAFER-945GSE 3.5” MotherboardPage 22  Auto-Negotiation with Next Page capability  Supports PCI Express™ 1.1  Supports pair swap/polarity/s

WAFER-945GSE 3.5” Motherboard Page 23 Figure 2-12: PCIe Mini Slot 2.5.5 Intel® ICH7-M Real Time Clock 256 bytes of battery backed RAM is provided by

WAFER-945GSE 3.5” MotherboardPage 24 Figure 2-13: SATA Connectors SATA controller specifications are listed below.  Supports four SATA drives 

WAFER-945GSE 3.5” Motherboard Page 25Figure 2-14: Onboard USB Implementation 2.6 LPC Bus Components 2.6.1 LPC Bus Overview The SIS964 LPC bus is con

WAFER-945GSE 3.5” MotherboardPage 26  Console redirection function support  PXE (Pre-boot Execution Environment) support  USB booting support

WAFER-945GSE 3.5” Motherboard Page 27 Two 16C550 UARTs for serial port control  One IEEE 1284 Parallel Port  Keyboard Controller  Watchd

WAFER-945GSE 3.5” MotherboardPage 28 2.6.3.5 Super I/O Fan Speed Controller The Super I/O fan speed controller enables the system to monitor the spe

WAFER-945GSE 3.5” Motherboard Page 29 System temperature  CPU temperature Eight voltage inputs on the WAFER-945GSE Super I/O Enhanced Hardware M

WAFER-945GSE 3.5” Motherboard Page v NOTE: These messages inform the reader of essential but non-critical information. These messages should be read

WAFER-945GSE 3.5” MotherboardPage 30 2.7.3 Power Consumption 762H720HTable 2-1 shows the power consumption parameters for the WAFER-945GSE running w

WAFER-945GSE 3.5” Motherboard Page 31 3 Unpacking Chapter 3

WAFER-945GSE 3.5” MotherboardPage 32 3.1 Anti-static Precautions WARNING! Failure to take ESD precautions during the installation of the WAFER-945G

WAFER-945GSE 3.5” Motherboard Page 333.3 Unpacking Checklist NOTE: If any of the components listed in the checklist below are missing, do not proce

WAFER-945GSE 3.5” MotherboardPage 34 1 4 COM (wo bracket) (P/N: 32200-025401-RS) 1 Mini jumper pack (2.0mm) (P/N:33100-000033-RS) 1 Utility CD

WAFER-945GSE 3.5” Motherboard Page 35 4 Connectors Chapter 4

WAFER-945GSE 3.5” MotherboardPage 36 4.1 Peripheral Interface Connectors Section 765H723H4.2 shows peripheral interface connector locations. Sectio

WAFER-945GSE 3.5” Motherboard Page 37Connector Type Label Audio connector 10-pin header AUDIO1 ATX enable connector 3-pin wafer ATXCTL1 ATX pow

WAFER-945GSE 3.5” MotherboardPage 38 Connector Type Label Ethernet connector RJ-45 LAN1 Ethernet connector RJ-45 LAN2 RS-232 serial port conne

WAFER-945GSE 3.5” Motherboard Page 39 PIN NO. DESCRIPTION 1 +12V 2 GND 3 GND 4 +5V Table 4-3: ATX Power Connector Pinouts 4.3.2 ATX Power Supply E

WAFER-945GSE 3.5” MotherboardPage vi Packing List NOTE: If any of the components listed in the checklist below are missing, please do not proceed w

WAFER-945GSE 3.5” MotherboardPage 40 3 PS-ON Table 4-4: ATX Power Supply Enable Connector Pinouts 4.3.3 Audio Connector (10-pin) CN Label: AUDIO1 C

WAFER-945GSE 3.5” Motherboard Page 414.3.4 Backlight Inverter Connector CN Label: INVERTER1 CN Type: 5-pin wafer (1x5) CN Location: See 737HFigure

WAFER-945GSE 3.5” MotherboardPage 42 4.3.5 CompactFlash® Socket CN Label: CF1 CN Type: 50-pin header (2x25) CN Location: See 739HFigure 4-6 CN P

WAFER-945GSE 3.5” Motherboard Page 43PIN NO. DESCRIPTION PIN NO. DESCRIPTION7 HDC_CS0# 32 HDC_CS1 8 GROUND 33 N/C 9 GROUND 34 IOR# 10 GROUND 35 IO

WAFER-945GSE 3.5” MotherboardPage 44 Figure 4-7: DIO Connector Connector Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION1 GND 2 VCC 3 Output 3

WAFER-945GSE 3.5” Motherboard Page 45Figure 4-8: +12V Fan Connector Location PIN NO. DESCRIPTION 1 GND 2 +12V 3 Fan Speed Detect Table 4-9: +12V F

WAFER-945GSE 3.5” MotherboardPage 46 Figure 4-9: Keyboard/Mouse Connector Location PIN NO. DESCRIPTION 1 +5V KB DATA 2 MS DATA 3 MS CLK 4 KB DA

WAFER-945GSE 3.5” Motherboard Page 47 Figure 4-10: LED Connector Locations PIN NO. DESCRIPTION 1 +5V 2 GND 3 Power LED+ 4 Power LED- 5 HDD LED+ 6

WAFER-945GSE 3.5” MotherboardPage 48 Figure 4-11: LVDS LCD Connector Pinout Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GND1 2 GND2 3 A_

WAFER-945GSE 3.5” Motherboard Page 494.3.11 PCIe Mini Card Slot CN Label: CN4 CN Type: 52-pin Mini PCIe Card Slot CN Location: See 791H751HFigure 4-

WAFER-945GSE 3.5” Motherboard Page viiTable of Contents 1H1 INTRODUCTION...

WAFER-945GSE 3.5” MotherboardPage 50 17 PCIRST# 18 GND 19 LPC 20 VCC3 21 GND 22 PCIRST# 23 PERN2 24 3VDual 25 PERP2 26 GND 27 GND 28 1.5V

WAFER-945GSE 3.5” Motherboard Page 514.3.12 Power Button Connector CN Label: PWRBTN1 CN Type: 2-pin wafer (1x2) CN Location: See 753HFigure 4-13 C

WAFER-945GSE 3.5” MotherboardPage 52 The reset button connector is connected to a reset switch on the system chassis to enable users to reboot the s

WAFER-945GSE 3.5” Motherboard Page 53 Figure 4-15: SATA Drive Connector Locations PIN NO. DESCRIPTION 1 GND 2 TX+ 3 TX- 4 GND 5 RX- 6 RX+ 7 GND T

WAFER-945GSE 3.5” MotherboardPage 54  COM3 is located on pin 1 to pin 10  COM4 is located on pin 11 to pin 20  COM5 is located on pin 21 to pi

WAFER-945GSE 3.5” Motherboard Page 55PIN NO. DESCRIPTION PIN NO. DESCRIPTION 25 TRANSMIT DATA (TXD5) 26 CLEAR TO SEND (CTS5) 27 DATA TERMINAL

WAFER-945GSE 3.5” MotherboardPage 56 Figure 4-17: RS-232/422/485 Serial Port Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 NDCD

WAFER-945GSE 3.5” Motherboard Page 57Figure 4-18: USB Connector Pinout Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION1 VCC 2 GND 3 DATA- 4 D

WAFER-945GSE 3.5” MotherboardPage 58 Figure 4-19: WAFER-945GSE External Peripheral Interface Connector 4.4.1 LAN Connectors CN Label: LAN1 and LAN2

WAFER-945GSE 3.5” Motherboard Page 59 Figure 4-20: RJ-45 Ethernet Connector The RJ-45 Ethernet connector has two status LEDs, one green and one yel

WAFER-945GSE 3.5” MotherboardPage viii 31H2.5.6 Intel® ICH7-M SATA Controller ...

WAFER-945GSE 3.5” MotherboardPage 60 PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 DCD 6 DSR 2 RX 7 RTS 3 TX 8 CTS 4 DTR 9 RI 5 GND Table 4-22

WAFER-945GSE 3.5” Motherboard Page 61PIN NO. DESCRIPTION PIN NO. DESCRIPTION1 VCC (+5V) 5 VCC (+5V) 2 DATA4- 6 DATA5- 3 DATA4+ 7 DATA5+ 4 GND 8

WAFER-945GSE 3.5” MotherboardPage 62 PIN DESCRIPTION PIN DESCRIPTION13 HSYNC 14 VSYNC 15 DDCCLK Table 4-24: VGA Connector Pinouts

WAFER-945GSE 3.5” Motherboard Page 63 5 Installation Chapter 5

WAFER-945GSE 3.5” MotherboardPage 64 5.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the WAFER-945G

WAFER-945GSE 3.5” Motherboard Page 655.2 Installation Considerations NOTE: The following installation notices and installation considerations shou

WAFER-945GSE 3.5” MotherboardPage 66 o When working with the WAFER-945GSE, make sure that it is disconnected from all power supplies and that no el

WAFER-945GSE 3.5” Motherboard Page 675.3 Unpacking When the WAFER-945GSE is unpacked, please check all the unpacking list items listed in Chapter 3

WAFER-945GSE 3.5” MotherboardPage 68 Step 2: Align the SO-DIMM with the socket. The SO-DIMM must be oriented in such a way that the notch in the mi

WAFER-945GSE 3.5” Motherboard Page 69 Figure 5-2: CF Card Installation 5.5 Jumper Settings NOTE: A jumper is a metal bridge used to close an elec

WAFER-945GSE 3.5” Motherboard Page ix64H4.3.4 Backlight Inverter Connector ...

WAFER-945GSE 3.5” MotherboardPage 70 Description Label Type AT Power Mode Setting ATXCTL1 2-pin header CF Card Setting JCF1 2-pin header Clear

WAFER-945GSE 3.5” Motherboard Page 71AT Power Select Description Short 2 – 3 Use AT power Default OFF Use ATX power Table 5-2: AT Power Select

WAFER-945GSE 3.5” MotherboardPage 72 Figure 5-5: CF Card Setup Jumper Location 5.5.3 Clear CMOS Jumper Jumper Label: J_CMOS1 Jumper Type: 3-pin hea

WAFER-945GSE 3.5” Motherboard Page 73AT Power Select Description Short 1 - 2 Keep CMOS Setup Default Short 2 - 3 Clear CMOS Setup Table 5-4:

WAFER-945GSE 3.5” MotherboardPage 74 Short 5-6 Short 7-8 RS-485 with RTS control Table 5-5: COM 2 Function Select Jumper Settings The COM 2 Functio

WAFER-945GSE 3.5” Motherboard Page 75J_LCD_TYPE1 Pin 7- Pin 8 Pin 5- Pin 6 Pin 3- Pin 4 Pin 1-Pin 2 DESCRIPTION OFF OFF OFF OFF 640 x 480 18-bi

WAFER-945GSE 3.5” MotherboardPage 76 5.5.6 LVDS Voltage Selection WARNING: Permanent damage to the screen and WAFER-945GSE may occur if the wrong v

WAFER-945GSE 3.5” Motherboard Page 77 Figure 5-9: LVDS Voltage Selection Jumper Pinout Locations 5.6 Chassis Installation 5.6.1 Airflow WARNING: Ai

WAFER-945GSE 3.5” MotherboardPage 78 NOTE: IEI has a wide range of backplanes available. Please contact your WAFER-945GSE vendor, reseller or an IE

WAFER-945GSE 3.5” Motherboard Page 79 4-COM port kit 5.7.2 SATA Drive Connection The WAFER-945GSE is shipped with two SATA drive cables and one SA